>>>>>型号:AN-X2-AB-DHRIO 远程 I/O 或 DH+ 网关
【功能描述】
规格
远程I/O扫描器功能：
此模式允许用户用ControlLogix或CompactLogix PAC替换现有的远程I/O PLC，而无需更换现有的I/O机架。
在不中断现有控制的情况下构建新的控制器程序，最大限度地减少停机时间
支持多达32个机架的远程I/O
支持所有远程I/O波特率（57.6、115.2和230.4 K波特率）和0至76八通道的远程I/O寻址
适用于ControlLogix或CompactLogix
自动配置实用程序可发现波特率并映射离散I/O，从而减少配置错误
驾驶：
此模式支持将远程I/O上的传统Allen Bradley驱动器升级到启用了EtherNet/IP的新驱动器。
无需更改PLC代码
支持多达4个EtherNet/IP驱动器
可配置1/4、1/2和全机架寻址
支持EtherNet/IP上的所有PowerFlex变频器
人机界面
此模式允许将远程I/O或DH+上的传统PanelView升级为EtherNet/IP上的PanelView Plus、PanelView Plus 6或PanelView Plus 7。
无需更改PLC代码
在同一网络上支持多达8个PanelView
支持PLC5或SLC网络上的DH+到EtherNet/IP PanelViews升级
DH+型
这种操作模式充当EtherNet/IP和Data Highway Plus网络之间的桥梁。
EtherNet/IP网络上的编程终端和/或处理器可以访问DH+网络上的传统处理器
通过RSLinx下载到PLC5或SLC
通过Web浏览器进行配置
支持所有DH+波特率（57.6、115.2和230.4 K波特）
支持PLC5或SLC网络上的DH+到EtherNet/IP PanelViews升级
Flex I/O扫描器
此模式允许远程I/O上的PLC连接和控制1794-AENT EtherNet/IP Flex适配器。
设计用于替换过时的1794-ASB适配器
支持多达16个EtherNet/IP连接
每个适配器和离散机架都算作一个连接。每个模拟模块都算作一个连接
>>>>>型号:AN-X2-AB-DHRIO 远程 I/O 或 DH+ 网关
【英文介绍】
specification
Remote I/O Scanner Features:
This mode allows users to replace existing remote I/O PLCS with ControlLogix or CompactLogix PAC without having to replace existing I/O racks.
Build new controller programs without interrupting existing controls to minimize downtime
Supports up to 32 racks of remote I/O
Supports all remote I/O baud rates (57.6, 115.2, and 230.4K baud rates) and remote I/O addressing from 0 to 76 eight channels
Available for ControlLogix or CompactLogix
The auto-configuration utility discovers baud rates and maps discrete I/O to reduce configuration errors
Driving:
This mode allows you to upgrade a legacy Allen Bradley drive on remote I/O to a new drive with EtherNet/IP enabled.
No need to change the PLC code
Supports up to 4 EtherNet/IP drives
1/4, 1/2, and full rack addressing are available
All PowerFlex drives on EtherNet/IP are supported
Man-machine interface
This mode allows you to upgrade a traditional PanelView on remote I/O or DH+ to PanelView Plus, PanelView Plus 6, or PanelView Plus 7 on EtherNet/IP.
No need to change the PLC code
Up to 8 PanelViews are supported on the same network
DH+ to EtherNet/IP PanelViews upgrades are supported on PLC5 or SLC networks
DH+ type
This mode of operation acts as a bridge between EtherNet/IP and Data Highway Plus networks.
Programming terminals and/or processors on EtherNet/IP networks can access traditional processors on DH+ networks
Download to PLC5 or SLC via RSLinx
You can configure this parameter using the Web browser
Support for all DH+ baud rates (57.6, 115.2 and 230.4K baud)
DH+ to EtherNet/IP PanelViews upgrades are supported on PLC5 or SLC networks
Flex I/O scanner
This mode allows a PLC on remote I/O to connect and control the 1794-AENT EtherNet/IP Flex adapter.
Designed to replace the outdated 1794-ASB adapter
Supports up to 16 EtherNet/IP connections
Each adapter and discrete rack counts as one connection. Each analog module counts as a connection
>>>>>型号:AN-X2-AB-DHRIO 远程 I/O 或 DH+ 网关
