欢迎光临成都阳光熹禾电气有限公司官网!
工业设备配件供应 专业销售 库存齐全
全国咨询热线:18859254943
当前位置: 首页 > 产品展示 > GE
IS220PTURH1B
IS220PTURH1B
IS220PTURH1B
IS220PTURH1B
IS220PTURH1B
IS220PTURH1B

IS220PTURH1B 涡轮机I/O模块 允许自动重新配置

>>>>>型号:IS220PTURH1B 涡轮机I/O模块 允许自动重新配置 【功能描述】 IS220PTURH1B是GE为其Mark VI系统创建的组件。Mark VI是GE发布的用于燃气/蒸汽轮机管理的最终Speedtronic系统之一。IS220PTURH1B是主涡轮机专用主脱扣包。该组件在涡轮机控制终端板与一个或两个以太网网络之间提供电气接口。该电池组的输出

电话/Phone:18859254943 (微信同号)

邮箱/Email:sales@ygdcs.com

QQ:3561040004

产品详情

>>>>>型号:IS220PTURH1B 涡轮机I/O模块 允许自动重新配置

 


IS220PTURH1B-3.jpg


【功能描述】

 

 

IS220PTURH1B是GE为其Mark VI系统创建的组件。Mark VI是GE发布的用于燃气/蒸汽轮机管理的最终Speedtronic系统之一。

IS220PTURH1B是主涡轮机专用主脱扣包。该组件在涡轮机控制终端板与一个或两个以太网网络之间提供电气接口。该电池组的输出通过连接到相关端子板的DC-62引脚连接器进行。

IS220PTURH1B采用黑色外壳,带有空气流通开口。该外壳的正面有多个LED指示灯,以及一个IR(红外端口)。此包中不使用此端口。在这个外壳内,有一个处理器板、一个专门用于涡轮机控制的第二块板和一个模拟采集辅助板。该电池组安装到TTURH1C端子板上。处理器板有两个10/100以太网端口、闪存和RAM、一个用于识别的只读芯片、一个内部温度传感器和一个复位电路。

该IS220PTURH1B允许自动重新配置,自动从控制器下载到I/O包。重新配置包括基本负载、引导负载、固件和参数。必须启用自动重新配置才能执行此操作。这可以通过组件编辑器在Toolbox ST应用程序中启用或禁用。

该IS220PTURH1B具有一个带有四个无源磁性速度输入的接口。电路灵敏度可以检测2 RPM的转动齿轮速度,以确定涡轮机是否已降至零转速(涡轮机已停止)。电池组上的中值速度信号用于速度控制和主要超速跳闸信号。如果您需要更多信息,请查阅制造商的手册或数据表。


 >>>>>型号:IS220PTURH1B 涡轮机I/O模块 允许自动重新配置

IS220PTURH1B.jpg

IS220PTURH1B-2.jpg


英文介绍

The IS220PTURH1B is a component created by GE for its Mark VI system. The Mark VI is one of the final Speedtronic systems released by GE for gas/steam turbine management.

The IS220PTURH1B is a special main trip package for the main turbine. This component provides an electrical interface between the turbine control terminal board and one or two Ethernet networks. The output of this battery pack is performed via a DC-62 pin connector connected to the relevant terminal board.

The IS220PTURH1B comes in a black housing with an air outlet. The front of the housing has multiple LED indicators, as well as an IR (infrared port). This port is not used in this package. Inside this enclosure, there is a processor board, a second board dedicated to turbine control, and an analog acquisition auxiliary board. The battery string is installed on the TTURH1C terminal board. The processor board has two 10/100 Ethernet ports, flash memory and RAM, a read-only chip for identification, an internal temperature sensor, and a reset circuit.

The IS220PTURH1B allows automatic reconfiguration and automatic download from the controller to the I/O package. Reconfiguration includes base load, boot load, firmware, and parameters. You must enable automatic reconfiguration to perform this operation. This can be enabled or disabled in the Toolbox ST application through the component editor.

The IS220PTURH1B has an interface with four passive magnetic speed inputs. The circuit sensitivity can detect a rotating gear speed of 2 RPM to determine if the turbine has dropped to zero speed (the turbine has stopped). The median speed signal on the battery pack is used for speed control and primary overspeed trip signals. If you need more information, consult the manufacturer's manual or data sheet.

>>>>>型号:IS220PTURH1B 涡轮机I/O模块 允许自动重新配置

水波纹风名片设计 (1702363063)_0.jpg

水波纹风名片设计 (1702363063)_1.jpg


标签: IS220PTURH1B

联系方式

成都阳光熹禾电气有限公司

电话:18859254943

QQ:3561040004

电邮:sales@ygdcs.com

地址:成都高新区天益街北巷52号附14号2层

采购:IS220PTURH1B 涡轮机I/O模块 允许自动重新配置

产品推荐/ RELATED PRODUCTS