IC697BEM731 | 天才总线控制器模块 | 90-70可编程逻辑控制器

型号:IC697BEM731

　　Ald分辨率12bit

　　采样率5mhz, 2mhz, 1mhz, 500khz....

　　500赫兹

　　存储深度(每通道)512k样点/ch

　　触发方式 手动触发、内触发、外触发

　　工作方式 在线、离线(黑匣子)

　　信号输入v/q或v/icp

　　通讯接口rj45以太网接口

　　IC697BEM731是一款天才总线控制器模块，是GE Fanuc系列90-70可编程逻辑控制器(PLC)家族的一部分。该模块主要用于连接多达三十(30)个设备，并通过在同一总线上的所有配置设备之间传递令牌来传输数据。

　　IC697BEM731具有一个(1)通道用于与驻留在同一总线上的设备接口，一个(1)手持监视器(HHM)端口用于使用MS DOS或Windows编程软件配置器功能将配置下载到模块。

　　在交付IC697BEM731时，它没有提供定义的总线地址。组态软件默认设置的标准地址为153.6 Kbaud，总线地址为31。这个默认地址可以通过下载一个有效的配置到CPU来修改。配置153.6 k波特(标准)时，通信总线最大允许距离为2000ft;当配置为153.6 k波特(扩展)时，3500英尺;76.8 k波特时为4500英尺，38.4 k波特时为7500英尺。必须将位于同一总线或网络上的所有设备配置为相同的波特率，否则将无法建立通信或可能出现通信不稳定。

　　Model :IC697BEM731

　　Ald resolution 12bit

　　Sampling rate 5mhz, 2mhz, 1mhz, 500khz....

　　500 Hertz

　　Storage depth (per channel)512k sample point /ch

　　Trigger Mode Manual trigger, internal trigger, and external trigger

　　Working mode Online, Offline (Black box)

　　Signal input v/q or v/icp

　　Communication port rj45 Ethernet port

　　The IC697BEM731 is a Genius Bus controller module that is part of the GE Fanuc series 90-70 Programmable Logic controller (PLC) family. This module is primarily used to connect up to thirty (30) devices and transfer data by passing tokens between all configured devices on the same bus.

　　The IC697BEM731 has a (1) channel for interfacing with devices residing on the same bus, and a (1) Handheld Monitor (HHM) port for downloading the configuration to the module using the MS DOS or Windows programming software Configurator feature.

　　When the IC697BEM731 was delivered, it did not provide a defined bus address. By default, the standard address set by the configuration software is 153.6 Kbaud and the bus address is 31. This default address can be modified by downloading a valid configuration to the CPU. When configured with 153.6k baud (standard), the maximum allowable distance of the communication bus is 2000ft; 3500 feet when configured at 153.6k baud (extended); 4,500 feet at 76.8 k baud and 7,500 feet at 38.4 k baud. All devices located on the same bus or network must be configured to the same baud rate, otherwise communication will not be established or may be unstable.