>>>>>型号:AN-X2-AB-DHRIO 远程I/O系统 I/O支架
【功能描述】
Remote I/O Scanner Features:
模式支持升级旧版本的Allen Bradley远程I/O系统转换成ControlLogix 或者CompactLogix 系列PAC而无需替代已存在的I/O支架。
建立新系统无需中断已存在控制, 减少停机时间
最多支持32个远程I/O机架
支持所有远程I/O波特率(57.6, 115.2, and 230.4 K baud), 远程I/O地址从0至76
兼容ControlLogix和CompactLogix系统
自动配置软件搜索波特率分配离散I/O降低配置风险
Drive:
模式支持升级旧版本的Allen Bradley远程I/O驱动转换成EtherNet/IP驱动。
无需改变PLC 代码
最多支持4路以态网驱动
可配置1 / 4，1 / 2和全机架寻址
支持PowerFlex驱动以态网通讯
HMI
模式支持升级旧版本的Allen Bradley远程I/O驱动转换成PanelView Plus, PanelView Plus 6 或者 PanelView Plus 7 EtherNet/IP
无需改变PLC 代码
在同一网段最多支持8台PanelViews
支持在PLC5 or SLC网络中将DH+ 转换升级成EtherNet/IP PanelViews
DH+
模式支持EtherNet/IP和DH+网络之间的协议转换
支持EtherNet/IP的可编程终端, 或者处理器能够连接 DH+网络的处理器
通过RSLinx 下载到PLC5或者SLC
通过网络浏览器配置
支持所有DH+波特率(57.6, 115.2, 和 230.4 K baud)
支持EtherNet/IP的可编程终端, 或者处理器能够连接 DH+网络的处理器
支持在PLC5 or SLC网络中将DH+ 转换升级成EtherNet/IP PanelViews
Flex I/O Scanner
模式支持Allen Bradley远程I/O系统和1794-AENT EtherNet/IP Flex适配器之间的通讯
Des替代1794-ASB 适配器
最多支持16个 EtherNet/IP 连接
每个适配器和分离机架做为一个连接。 每个模拟量模块做为一个连接
>>>>>型号:AN-X2-AB-DHRIO 远程I/O系统 I/O支架
【英文介绍】
Remote I/O Scanner Features:
Mode supports upgrading older versions of Allen Bradley remote I/O systems to ControlLogix or CompactLogix series PACs without replacing existing I/O mounts.
Build new systems without interrupting existing controls, reducing downtime
Supports up to 32 remote I/O racks
Supports all remote I/O baud rates (57.6, 115.2, and 230.4 K baud), and remote I/O addresses from 0 to 76
Compatible with ControlLogix and CompactLogix systems
Automatic configuration software searches for baud rates and allocates discrete I/ OS to reduce configuration risks
Drive:
The mode supports upgrading the Allen Bradley remote I/O driver of an earlier version to an EtherNet/IP driver.
No need to change the PLC code
Supports a maximum of four state network drivers
1/4, 1/2 and full rack addressing are available
Support PowerFlex driver to state network communication
HMI
The mode supports upgrading the Allen Bradley remote I/O driver of an earlier version to PanelView Plus, PanelView Plus 6, or PanelView Plus 7 EtherNet/IP
No need to change the PLC code
A maximum of eight PanelViews can be configured on the same network segment
DH+ conversion to EtherNet/IP PanelViews is supported on PLC5 or SLC networks
DH+
Mode Supports protocol conversion between EtherNet/IP and DH+ networks
A programmable terminal that supports EtherNet/IP, or a processor that can connect to a DH+ network
Download to PLC5 or SLC via RSLinx
Set this parameter using a web browser
Support for all DH+ baud rates (57.6, 115.2, and 230.4 K baud)
A programmable terminal that supports EtherNet/IP, or a processor that can connect to a DH+ network
DH+ conversion to EtherNet/IP PanelViews is supported on PLC5 or SLC networks
Flex I/O Scanner
The mode supports communication between the Allen Bradley remote I/O system and the 1794-AENT EtherNet/IP Flex adapter
Des replaces the 1794-ASB adapter
Up to 16 EtherNet/IP connections are supported
Each adapter and separate rack act as a connection. Each analog module acts as a connection
>>>>>型号:AN-X2-AB-DHRIO 远程I/O系统 I/O支架
